Home > Hard Drive > Installing 5 IDE Devices On A 2 IDE Socket Motheraboard.

Installing 5 IDE Devices On A 2 IDE Socket Motheraboard.


Video Tips Start the PC, go to CMOS (setup page to BIOS) by pressing F2 in Intel Machines or Press "Delete" in Non-Intel Machines. I think I have a newer version of IDE on my motherboard. Q04: What is Enhanced-IDE (EIDE) and Fast-ATA? Yvo ro 20.726 visualizaciones 2:31 Disco SATA en Board IDE - Duración: 8:50. this contact form

So, to make it a slave device, I place a jumper over the central (second) pair. It was driving me crazy. If you don't want to reinstall Windows, you can clone the contents of your old hard drive to your new one using the setup utilities that hard drive manufacturers provide, or Please start a New Thread if you're having a similar issue.View our Welcome Guide to learn how to use this site. http://www.makeuseof.com/tag/install-ide-hard-drive/

How To Connect Ide Hard Drive To Sata Motherboard

Thanks. hak1985org 93.480 visualizaciones 15:13 Hard Drive Not Recognized? or what i'v done wrong?

Thanks in advance! Yes No Not Helpful 1 Helpful 10 If I already have data in the second hard disk, will it all be gone when I format it? Mostrar más Cargando... How To Install Ide Hard Drive New box HD is SATA.

In the window that comes up, click Disk Management in the left pane. Ide Hard Drive Jumper Settings I knew some of the terms, but it took a few minutes to learn what they were and then followed the clear steps to install, config and run the two drive Do I require any jumpers on these drives if I were to hook up 2 SCSI drives together?

I bought a new hard drive and used the Restore CD to format it.

Im very sure I have it connected correctly, but when I boot up and try to enter the setup it takes a very long time and eventually goes black bar a Seagate Ide Hard Drive Jumper Settings If I disconnect the second drive the third one appears and vice versa. Hieu Nguyen 24.818 visualizaciones 2:02 Переходник IDE-SATA - Duración: 6:35. Свой лунапарк 37.401 visualizaciones 6:35 2.5 IDE to 2.5 sata - Duración: 1:15. 香吉士 10.102 visualizaciones 1:15 Посылка №87. Контроллер-переходник SATA by R.

Ide Hard Drive Jumper Settings

Esta función no está disponible en este momento. All is good except for the fact that my hard drive has a "C" and an "I". How To Connect Ide Hard Drive To Sata Motherboard Then you connect the bracelet to something grounded (like a copper pipe or the center screw on a wall outlet's face plate). How To Connect Ide Hard Drive To Motherboard Return to Questions Q02: What does the IDE interface actually do?

You can get a bracelet for a few dollars. http://secondsolution.net/hard-drive/installing-hdd-help.php It's better to have SATA for primary, but the speed wouldn't be a big difference Flag Permalink This was helpful (0) Collapse - I have a problem with mine by Laurenksmith You will be prompted during the first part of setup to partition and format your drive; if you are using Windows 2000, XP or Vista, make sure to use the NTFS Would you please kindly walk me thru?. Sata And Ide Hard Drives Together

The power supply of the enclosure that is, not the drive. Prior settings of the jumpers to "slave" would result in no boot screen at all upon powering on. Short URL to this thread: https://techguy.org/82871 Log in with Facebook Log in with Twitter Log in with Google Your name or email address: Do you already have an account? navigate here Flag as...

The IDE ribbon comes off of optical drive. How Many Hard Drives Can Be Connected To A Single Ide Cable To use the new drive as a second drive, the primary partition option should still be selected, otherwise, Windows will not format the drive.Thank you again. the drive is working properly.

share|improve this answer answered Feb 12 '11 at 12:11 Anthony Giorgio 491411 add a comment| up vote 0 down vote you could also install a floppy controller card if you have

For Serial ATA drives (SATA), you don't need to worry about jumpers at all. Read more. EditRelated wikiHows How to Recycle Old Computer Hard Drives How to Clear the Memory on Your Computer's Hard Drive How to Copy Contents of One Hard Drive to a New Hard Why Is It Necessary To Partition The Hard Disk While Installing Operating System? by rmazzeo / July 25, 2005 11:03 AM PDT In reply to: I have a problem with mine Hey Laurie,Yours is the first post I've come across that describes (almost) the

Take a look at one of your other devices to work out which the power cables are in your case. The IDE connector is also easy, the same as the motherboard it Flag Permalink This was helpful (0) Collapse - 1. Why can I start a root shell with sudo even with a '! ' in its shadow entry? his comment is here He spends an absurd amount of time in the VR room and tinkering with DIY home automation systems.

Line the new drive up with the opening of the drive bay and gently slide it into position, push it all the way in until the front of the drive is Sometimes it woudl boot up and sometimes it wouldn't. i have a question tho,, i want to add a second drive simply for photo work. Warnings Be careful when you create partitions.

advertisement To install your optical drive you will need: Compatible CD recorder or DVD drive (SATA or IDE). 4 securing screws (supplied with your CD recorder / DVD writer). I've hooked up all the cables and turned the drive to "On" in the Setup Utility. just look at the power connectors in your computer, then double check what connector your drive requires and go buy it. however it states no operating system when he boots it.

Some SATA drives do have a jumper which controls the speed of the SATA drive itself, but you do not need to worry about anything related to master, slave or cable Información Prensa Derechos de autor Creadores Publicidad Desarrolladores +YouTube Términos Privacidad Política y seguridad Enviar sugerencias Probar las nuevas funciones Cargando... Flag Permalink This was helpful (1) Collapse - It's all about the controllers by DJPython / July 22, 2005 5:53 AM PDT In reply to: Mixing SATA and IDE drives in After you open up your computer's case and look inside, you will probably find one optical drive (a CD or DVD drive), a single hard disk drive and perhaps a floppy

Once I found you I was just a few minutes from nirvana! Had to buy a "new" hard drive from Hunter Engineering, and Frankenstein some old parts together. Its simple:BECAUSE THE PEOPLE WHO DO KNOW WHAT IT MEANS WON'T NEED A GUIDE TO HELP THEM.Therefore, the people who don't know DO need a guide, but this guide is USELESS AvoidErrors 821.108 visualizaciones 4:23 How to access a hard drive from a dead computer. - Duración: 5:41.

It still has 2.79 GB of space used. Q02: What does the IDE interface actually do? Flag as duplicate Thanks! A special bit (the DRV bit) is used in the Drive/Head Register to distinguish between the controllers.

By the four sentence, you are assuming that everyone reading this will understand what ‘jumpers' are.