Home > Hard Drive > Installing A New Hard Drive & ATA/100 PCI Card

Installing A New Hard Drive & ATA/100 PCI Card

Contents

Should be beside where the optical drive ide cable plugs into the mobo. In its left list expand Storage if necessary and choose Disk Management. Raptor HD for it. Then I skip copy from drive. http://secondsolution.net/hard-drive/installing-a-new-hard-drive-easy-or-hard.php

This setting completely eliminates the need for additional drivers. I have them reconnected this same way. How We Test Laptops Still lost? Flag Permalink This was helpful (0) Collapse - That isn't the topic, but...

Maxtor Hard Drive Jumper Settings

Reply JP on August 10, 2007 at 5:06 pm I'm trying to add a second SATA hard drive to my Dell. Well, thing is, I have 900GB of data on the drive that I cannot lose. I expect you want all three to be used as single volumes of full drive size, as opposed to splitting each into smaller Partitions treated as individual drives. Reply Alan Bush on November 26, 2008 at 11:12 pm At last!!

A new window opens. Reply Steve on November 13, 2007 at 10:15 am Hi my problem is that my new replacement HD (my old one had a catastrophic failure) does not seem to be recognised Reply Dyan on December 22, 2007 at 11:20 am Joshcore, I purchased an external HDD caddy, and am trying to install and format an IDE 2.5″ hard drive (160GB, max partition Maxtor Diamondmax Plus 9 Jumper Settings This also means that you?ll likely need an adapter (available at any pc shop worth its salt) to get the 3 ? ?

Reply Kramium on June 28, 2008 at 10:14 pm G'day David Risley,Great help from your website! I have done this! Now I want to remove this and install Ubuntu. http://www.tomshardware.com/forum/44531-32-help-installing-200gb-hard-disk-promise-ata100 More-recent desktops may use (or just support) SATA drives but should support IDE, too.

You also need to under stand about setting jumpers on the hard drives. Maxtor N256 Jumper Settings I really need to start working and I was not able to install the new Western Digital WD2000JB-00DUA0 hard drive with a Promise ULTRA100 ATA TX2 PCI card (2.0.0210.2). A system normally will have one Boot Drive, specified in the BIOS Setup Boot Priority Sequence, and may have several other non-bootable drives. This way when I travel with my laptop I just unhook the drive from the desktop and stick it in my case.

Maxtor Diamondmax Plus 9 80gb Ata/133 Hdd

Only happening when trying to install Steam games solved Trying to install windows 7 on USB and can't detect my hard-drive. If not, I'd just apply that $20 towards another high-performance SATA drive and give the old IDE to a friend or relative.Submitted by: Sherry B. Maxtor Hard Drive Jumper Settings Reply John Oliver on May 23, 2008 at 4:02 pm Excellent article. Maxtor N256 Hard Drive Specs But keep in mind that the power supply may not be able to handle the additional drain. 5.

Depending on your MB's built-in controller, you may even be able to set up a RAID configuration, to gain reliability, speed, or both.Hope this helps,Best luck whichever way you decide to weblink Have done this many times for hard drives that have a ‘bad spot' that didn't allow it to be recognized on boot-up. Use caution when routing those wide ribbon cables to avoid blocking air flow. Posted by: mas42 (see profile) - 05/12/2006 8:28 AM[/QUOTE]That is totally untrue. Maxtor Sata Hard Drive Jumper Settings

There are two cables: the ribbon cable (or SATA cable) and the power cable. By the fifth sentence, ‘Serial ATA'. IF there is a second device, it MUST be designated the Slave. navigate here by raoulleon / May 14, 2006 2:00 PM PDT In reply to: re: Thanks, that's what I thought.

Flag Permalink This was helpful (0) Collapse - Not Odd by pmchefalo / May 11, 2006 9:10 PM PDT In reply to: very odd I built a PC based on an Maxtor 80gb External Hard Drive Groton, NY (AKA: Zepper) Discussion is locked Flag Permalink You are posting a reply to: 5/12/06 Adding old hard drive to new PC with only SATA connections The posting of advertisements, Reply David on April 19, 2008 at 7:41 am Great!

Reply Brett on June 4, 2009 at 2:31 pm Thanks so much for this post.I installed a 1TB SATA drive and it showed up fine in the BIOS but XP acted

With XP and 2000, though, use Windows' Disk Management utility. If he doesn't have an extra space on the legacy ATA controller, I would have to suggest getting SIIG products. There goes the ol' rebate. .bh. Maxtor Diamondmax Plus 9 160gb thanks.

In Windows 2000/XP/Vista, your new drive will not appear at all in My Computer until you format it. Uses the same controller, drive head, etc. The W2K also detected the new drive when I try check in the ‘device manager'.However, there isn't one WD SATA HD in the explorer. his comment is here The bios detected the drive and reboot.

This has an impact on how the SATA ports are set up.4. tosh9iAug 23, 2009, 2:03 AM I apologize,it appears you were actually right about the PATA + SATA settings. Use of any content or images without expressed permission is not allowed, although links to any page are welcomed and appreciated. Thus a 200x CF card should provide 30 MBps performance, 233x should equal 35 MBps speed, and a 266x card should hit 40 MBps.

Saved me a lot of messing around.Just the right amount of geekiness in my opinion for what it's worth! My current hard drive is a 250 GB seagate IDE drive that has the OS on it. Western Digital has created a monster. Joshcore, if you are blindly defending your precious website PC Mech, then please, at least have a decent reason to do so.

EXCELLENT!!!!thanks guys for creating this it sure is a help for newbies out there 🙂 as Kyle said waaaaaay back, "I did'nt know that disk management exist" hehehe Reply Bill R I use and recommend this controller, http://www.syba.com/product/43/02/01/2/index.html as it is reliable, inexpensive and based on a SIL chipset. Are you using the Promise ATA 100 TX2 card? Thanks for the easy to follow instructions.