Home > Hard Drive > Installing A Slave SATA Drive

Installing A Slave SATA Drive

Contents

Cargando... Publicado el 29 sept. 2014http://www.anetcomputers.com/secondar...How to install a secondary SATA hard drive. Once seated in the drive cage, use the screws that came with the drive to secure it – you will need to align the holes on the drive with the holes X:\Program Files Also this will be great insurance in case your system won’t boot, requiring you to perform a clean installation on C – rather than betting fingers crossed on Data this contact form

TechPlayground 60.167 visualizaciones 6:54 How to completely format an IDE (PATA) hard disk drive to its full capacity by deleting its MBR - Duración: 34:40. Even the PCs I drag out of the local dump have SATA drives nowadays (uhh, not that I do that often or anything, but .. This is nevertheless a very useful guide and very clear so thank you for it(I have bought several drives and they haven't had screws again check ebay or your local repair Type diskmgmt.msc and enter 3. learn this here now

How To Install A Second Sata Hard Drive

As long as you have a Windows drive installed in the system, your computer will recognize the additional drive as a secondary. 1. If you're having difficulty, it's a good idea to consult your manual on how your particular case is removed. Iniciar sesión Estadísticas Añadir traducciones 14.021 visualizaciones ¿Te gusta este vídeo? Flag as duplicate Thanks!

Jumpers are used to configure certain devices including optical drives and IDE hard drives. About.com 523.205 visualizaciones 3:17 Install a new larger Hard Drive and format it with ease - Duración: 9:47. But by and large, installing a new SATA drive in your Windows 7 desktop PC is a lot like falling off a log. How To Slave A Sata Hard Drive Check the "Perform a quick format" box, then click "Next" and "Finish." Things Needed SATA data cable References (4) PC World: Instructions on How to Install SATA Hard DrivesChengdu Yiwo Tech

Reply Ardiana December 31, 2016 at 3:27 pm IDE cables normally have 3 outlets, one for motherboard and two for hard drives/ CD drives. right-click > extend volume > next 4a. So, keep in mind to buy a device that is in align with max supported port speed to get the max performance.

Refer to the chart below if you’re unsure.

Only SATA-enabled motherboards will accept these drives. How To Connect Two Sata Hard Disk In One Pc Installing SATA drives is much simpler than installing IDE hard drives because SATA drives don't have any master and slave jumper settings to fiddle with. from MAXIMUM SPACE AVAILABLE IN MB input the amount you want in SELECT THE AMOUNT OF SPACE IN MB > next > finish this is simple maths extend is + (android Britec09 491.562 visualizaciones 10:01 Add a second hard drive to your pc - Duración: 9:18.

How To Install A Second Hard Drive Windows 7

Click "Next." 14. http://smallbusiness.chron.com/connect-sata-hard-disk-slave-56859.html Switch to another language: Catalan | Basque | Galician | View all Cerrar Sí, quiero conservarla. How To Install A Second Sata Hard Drive TechPlayground 60.167 visualizaciones 6:54 Install a Second IDE Hard Drive - Duración: 9:41. How To Install A Second Hard Drive Windows 10 Reply nizbot January 22, 2011 at 12:49 am Title of article should probably reflect that this is more for your standard desktop mid or full tower PC.

Change all fields to auto detection. http://secondsolution.net/hard-drive/installing-slave-hard-drive.php Reply cezar August 6, 2016 at 9:56 pm I have an old sata HD that came with the PC but the capacity was way to small, so i put in my Will my windows 7 sata hard drive function as a slave disk? So, in the case your new HDD has no active partition (windows is not installed in it – it is used as an internal flash drive for storage purpose), I personally What Is A Slave Hard Drive

Let’s do this! 1. Subscribe to Our Newsletter Email: Advertisement Scroll down for the next article © 2017 MakeUseOf. If you are replacing a drive then it can be installed in the same drive bay as the old one. http://secondsolution.net/hard-drive/installing-xp-on-a-slave-drive.php One end of the cable should be connected to your computer's power supply, and the other is a black plug with a matching L-shaped connector. 6.

Also make sure that you did not insert the cable upside down. Sata Hard Drive Slave Jumper Setting Obviously, that isnt outdated. Also, to reduce the risk, handle your hard drive as little as possible; pick it up and put it in, don't fool around with it.

Learn how & Discover other computing alternatives: http://ow.ly/nfI8w Categoría Consejos y estilo Licencia Licencia de YouTube estándar Mostrar más Mostrar menos Cargando...

RESPECT: James Bruce - simply modest and virtually real Keep up the good work! If you are adding a second drive then try and leave a gap between the two drives for ventilation, although this might not always be possible. Put it in the 'maybe' category. :) Reply Leave a Reply Cancel reply Your email address will not be published. Master Slave Hard Drive Setup In the case both the HDDs are IDE, you need to specify and let know the BIOS which drive from which to boot – i.e.

We’ll be focusing only on the hard drive today, but the guide will give you a great overview on all the random sockets and ports you’ll see on the motherboard once Reply James Bruce October 5, 2016 at 5:00 pm Depends on the shop, but anywhere with a "geek helpdesk" style service should be able to do that for you, yes. the Global Study Desk nadun flower Reply Priyankar November 22, 2016 at 4:11 am I did the same as you written in the post but didn't find the 2nd HDD option his comment is here Unlike older IDE drives, SATA disks have no jumpers and it's not necessary to configure a master/slave relationship between them.

The hard drive is a fairly sizeable chunk of metal like this: You should find it sitting in a metal cage of some sort. For example, a modern SSD is likely to support the SATA III standard, also known as SATA 6.0Gb/s. I did everything is great on the old good HD, but i can't access the failing HD. If you have a spare power cable but it isn’t SATA, you can still get a second drive but you’ll need to make sure it can accept a MOLEX type power