Home > Hard Drive > Installing An ANCIENT (120mb) HDD As A Slave On A Modern System

Installing An ANCIENT (120mb) HDD As A Slave On A Modern System

Contents

Table of Contents QUESTION:SCSI sounds interesting. I resoldered every joint. Step 3: Remove the hard disk from the 386 and attach it to your host PC, it should be MASTER on Channel 0 and the drive with the FAT16 partition we Now that I know how to properly configure a Linux distro (and what not to install on a machine slower than my calculator)…I could make that system fly. :) Report comment this contact form

Because SCSI drives are produced in lower volume they cost more to produce. Never fear I will be covering that in a part II later this week. Waiting for interrupt during drive seek will completely free the bus for DMA controller. ATA requires significant interrupt service overhead from the host to handle this. https://forums.techguy.org/threads/installing-an-ancient-120mb-hdd-as-a-slave-on-a-modern-system.164287/

What Is A Slave Hard Drive

Read more. Results 1 to 11 of 11 Thread: Installing ANCIENT (120mb!!!) into modern computer Tweet Thread Tools Show Printable Version Email this Page… Subscribe to this Thread… Search Thread Advanced Search Sounds like Intel is trying to make EIDE into SCSI, eh? No desktop or anything else graphical, but it is able to run Apache and Samba.

Or the block may be closer to the head than process A's block, or on a different drive on the same cable. Interesting? You may need to have your boot partition within the first 8GB, though. How To Install A Second Sata Hard Drive These old machines just weren't designed with 2gb+ partitions in mind I guess :p __ Trevor k2x4b524[March 16th, 2010, 12:43 AMI am unable to update my chips to RC2 from RC1,

Andrew Lynch salamontagneMarch 8th, 2010, 10:57 AMThats kinda where i was going....WD drives have been notorius for spec issues. How To Slave A Sata Hard Drive aitotatMarch 1st, 2010, 11:12 PMI later found out that a hard drive works fine, only the IDE-CF adapter wouldn't boot with the MF card installed. The older hard drive, however, isn't being detected. I had 2 dead ones and this fix it.

Once at the DOS prompt use FDISK to setup a 100 or so meg partition, be sure to tell FDISK no when it asks you if you want large disk support How To Connect Two Hard Disk In One Pc It comes on a two-floppy distribution, features add-ons for networking and user access, and can even use the packages from Slackware 4.0 (still available if you look hard enough) for additional Just a little heads up. :-) Re:A long awaited distro (Score:2) by dada21 ( 163177 ) * writes: I tried one and I hated the keyboard. Web pages have gotten compicated enough that and old CPU takes more time to render the page than the modem takes to bring in the data.

How To Slave A Sata Hard Drive

The bus reset is necessary when the controlling host has failed and left the shared device reserved. find more Report comment Reply dolo724 says: August 15, 2011 at 10:28 am Could you have left the HDD in place? What Is A Slave Hard Drive What's going on? How To Connect Two Sata Hard Disk In One Pc I had to do the same thing for the hard drive from a pentium 133, and it went off without a hitch--XP detected it and its two windows 95 (FAT16?) partitions,

Last night I went to the WD website to see if there was any helpful software as salamontagne suggested. weblink I am using a plain jane IBM XT with IBM floppy controller. Re:Get the PUPPY! (Score:5, Interesting) by hey! ( 33014 ) writes: on Monday November 28, 2005 @01:57PM (#14131089) Homepage Journal I like it too, but each has its place.Puppy is designed Table of Contents Platform Specific Questions: What are the general steps I need to do to install a SCSI disk to be used with Windows? Master Slave Hard Drive Jumper Settings

But it's based on Knoppix and is intended to be run as a Live CD, not installed onto a system. Very, very, slow. There are areas of SCSI which I am not expert on, and when a question of fact comes up in one of those areas, I research the issue using the SCSI http://secondsolution.net/hard-drive/installing-xp-on-a-slave-drive.php Report comment Reply rso says: August 13, 2011 at 2:52 am try ttylinux, or blue dot linux.

Thus, for my use, it's acceptable fast.I do have to add that I've scrapped (or are scrapping) most of my older hardware. Master Slave Hard Drive Setup After the boot sector is loaded, the O/S's device drivers take over and those can be unloaded or drive letters re-ordered via the O/S configuration tools. That wouldn't be possible if you give an average person a kernel and ask expect them to solve their problems with drivers and whatnot.

My drive stopped working.

Good luck. ASUS A7N8X dlx | 2100XP | 512 PC3200 | MSI G4MX440-8X 128Mb | WD 60Gb & 160 Gb | 400W Allied PS | Logitech Cordless Duo KBD & Mouse | Hitachi Vector (Score:5, Informative) by RailGunner ( 554645 ) * writes: on Monday November 28, 2005 @01:26PM (#14130801) Journal Based on slackware, optimized for older hardware, and there's also a SOHO edition How To Install A Second Hard Drive Windows 10 I often hear the whine "It seems to be working, why should I bother with the terminators?" The following appropriate analogy was given to me by Kevin Kilzer: "It only seems

If you plan to use only two drives (one per IDE channel), IDE will probably be slightly faster and definitely less expensive than SCSI. Another big issue: ATA does not allow more than one I/O request to be outstanding on a single cable, even to different drives. One thing I do know is that WD has always been notorious for being the only one of the major brands that is pedantic about the distinction between "master" and "single". his comment is here Once you've partitioned it, you can set it up from your snazzier (read: actually usable) computer.

Glad you got it working! This provides high reliability. It's not a toshiba, is it? I saw this on PC Advisor and thought you should see it too.

You are doing a great job and have the patience of a saint. perMarch 2nd, 2010, 01:37 PMYes, I was using flash.com. What am I doing wrong? Vintage Computer Forum > Technical Support > Vintage Computer Hardware > XTIDE tech support thread PDA View Full Version : XTIDE tech support thread Pages : [1] 2 3 hargleFebruary 27th,

under 13 watts no moving parts. An old distro will be small enough to avoid it all together, but a new one will rely on it frequently. However, I have DOS doing way more than Linux probably could on that hardware, just because of speed issues. make-use-of-logo logo-background menu search search-start close email bookmark facebook google twitter pinterest stumbleupon whatsapp amazon youtube youtube label-rectangle triangle-long down PC & Mobile Windows Mac Linux Android iPhone and iPad Internet

Build instructions are here: http://wiki.vintage-computer.com/index.php/XTIDE_build_instructions Main wiki page, with links to BIOS and other info: http://www.wiki.vintage-computer.com/index.php/XTIDE_project Jumpers: http://i870.photobucket.com/albums/ab264/hargle/jumpers.jpg You need 3 jumpers for the card to operate correctly. This site is completely free -- paid for by advertisers and donations. CF cards and microdrives only use the 5V line.