Home > Hard Drive > Installing Primary Slave (hard Drive)

Installing Primary Slave (hard Drive)

Contents

If you wanted to attach two hard disks to the same channel, one had to be set to be the master, the other the slave. If the CD-ROM is far from the hard drives, you will need one cable for the hard drives, and another going to the CD-ROM. Note: If you want to recover data from the "OLD" drive, don't do this! To get around this you'll want to use that install disk that came with the hard drive or if you're a relatively advanced user a BIOS update should be available. http://secondsolution.net/hard-drive/installing-slave-hard-drive.php

Enable LBA mode and UDMA mode, if applicable. Ask us. Although you'd better destroy it or put it in another computer. If you are permanently installing an old drive on a new computer you may be slowing the system down a bit.

How To Slave A Sata Hard Drive

I may just do a clean install then move my files over. Drive is Slave - Use this setting if the drive is an additional drive on the cable and the original drive is set as Master. Shut down the computer and unplug all cables from the tower. 2.

The IDE cable will be marked down one side with a red or black strip, this denotes Pin 1, match this with the pin 1 indicator on the back of the They gave me permission and directions to use USB Flash or Jump drive to place ISO on. I even took an old hard drive and put it in an external USB case/kit and use it just for storing my digital photos. Sata Master Slave It all depends on how important the information is that's on the drive.

If you're adding an IDE drive as a second drive, you may be able to connect it to the same data cable as your primary IDE drive, or along with an Master Slave Hard Drive Setup That means no jumpers to set and no fear of getting it wrong. A lot of people like to use what is called Cable Select. It's also a good idea to touch the power supply before you go sticking your hands in there!

instructions, set the jumpers correctly I even had Windows XP install running. How To Connect Two Sata Hard Disk In One Pc RealBeastMar 16, 2015, 9:24 PM Nope, you can install Windows 7 to a drive that is not even initialized, Win 7 does it as the first step, so no need to A few years ago, before SATA, adding a second hard drive was made more complicated due to the fact that PATA (also known as EIDE) required a master/slave relationship. When the old drive dies, and it will, that's the time to replace it and retrieve those same files from the main drive to the newest one.

Master Slave Hard Drive Setup

JUST ENSURE YOU SET YOUR JUMPER TO SLAVE SETTINGS PRIOR TO INSTALLATION.

One end of the cable should be connected to your computer's power supply, and the other is a black plug with a matching L-shaped connector. 6. How To Slave A Sata Hard Drive Right-click in this area and select "New Simple Volume." 12. Master Slave Hard Drive Jumper Settings Let's Begin Unpack everything.

Comments Comments Samsung Galaxy A5 2017 review: A Galaxy S7 lookalike with a much lower price 1995-2015: How technology has changed the world in 20 years VR painting & modelling tools http://secondsolution.net/hard-drive/installing-xp-on-a-slave-drive.php She earned a B.A. I would just make sure to install your Master Drive first then add your slave drive, an extra step that can save a lot of confusion. If you only want one large volume on the disk (most common), you can leave this value as is. How To Install A Second Sata Hard Drive

You don't just install from the ISO off a USB stick, it needs to be bootable and the tool will do that for you and provides good instructions. Powered by Mediawiki. In this case you will use the Molex connector for power, see fig 1.5 above for an example of this connector. http://secondsolution.net/hard-drive/installing-old-hard-drive-as-a-slave.php Most hard drive kits include a data cable (SATA or IDE, depending on the drive), a power adapter cable (with some SATA drives), and screws.

Both my jump and flash drives are Fat32 not NTFS. How To Install A Second Hard Drive Windows 10 But remember, that programs from that old hard disk probably won't run, because they will have to be installed into the new Windows again. Hinzufügen Playlists werden geladen...

Then, revisit steps 3 and 4 to direct your PC to boot from the new drive.

it said it had an error that read "failed to retrieve source information 205500(0322bc)". Flag Permalink This was helpful (0) Collapse - Sounds like good advice, Thor2k by grandpaw7 / August 30, 2004 6:25 AM PDT In reply to: Re: Thanks, datalookup I haven't discarded There will be a plastic sleeve covering two of the pins, if not then check the hard drive packaging to locate it. Sata Hard Drive Jumper Settings They might even come with a 160 gig or above HD.

Here, we installed Seagate's Barracuda 7200.10, a $124, 320GB Serial ATA (SATA) drive, inside a Dell Dimension 8400 running Windows XP Home Edition. If you're installing a SATA drive as secondary storage, follow the data cable from your current drive (assuming it's SATA, too) to the other end. by R. http://secondsolution.net/hard-drive/install-old-98-hard-drive-as-slave-on-xp-as-is.php Plug a SATA power cable into the long L-shaped connector on the back of your hard drive.

If you've got an HDD over 5 years old, consider it ready to die at any moment. After formatting it, use Norton Ghost (or a similar program) to clone your boot drive's contents to the new drive. Allow the computer to boot normally and you should see all your drives (C, D, E, F…). When you reboot your machine the BIOS should automatically detect the new hard drive.

It is sometimes easier to remove the IDE data cable and the power cable (labeled A and B in fig 1.1) before you remove the fixing screws (see fig 1.1), as Make sure the power is plugged in and everything is connected securely. Primary SATA won't boot when IDE Slave laptop HDD is plugged into a PC Primary Slave HDD Error Can't find your answer ? Costly especially if only to transfer data from 1 pc to the other and then never to be used again.

The letter assigned to the hard drive will depend on your machine's configuration. Tips Typically a computer can have up to 4 drives.