Home > Hard Drive > Installing Slave IDE HD Using IDE-SATA Converter

Installing Slave IDE HD Using IDE-SATA Converter

Contents

Inicia sesión para que tengamos en cuenta tu opinión. Añadir a ¿Quieres volver a verlo más tarde? Nothing I can't live with now that I finally got both HD's working. my dvd rewriter uses ide cable , now when i plug the ide hard drive in and set the sata as boot it shows in the bios and gets stuck at this contact form

Acción en curso... Advertisement On the motherboard end, the socket looks like this. Of the two (possible) devices sharing a port / cable, ONE MUST be the Master of that port, and its jumper set according to the diagram on the HDD unit itself. The IDE port is a 40-pin connector, Floppy is 34 pin.

How To Connect Ide Hard Drive To Sata Motherboard

CyberTech 186.384 visualizaciones 2:02 How to install SATA hard drive into a computer - Duración: 6:52. Hi, I too have an Asus A8N SLI Premium, and have been fighting this machine the past couple of days trying to figure out how to get this to work. Cambiar a otro idioma: Català | Euskara | Galego | Ver todo Learn more You're viewing YouTube in Spanish (Spain). Most likely you set your jumper wrong.

I have OS's on both drives and can boot from either by selecting which one I want to be the primary at startup(note this will have an effect on drive letters). If you have this backwards the drive will normally either be silent or fail to power up. I was told because I wiped out a registry entry (related to the SATA drive setup) and there was a problem due to the fact Windows 2000 can't see anything over Why Is It Necessary To Partition The Hard Disk While Installing Operating System? IDE cable (if required).

The problem is that when she plays the CDs on the ... Sata And Ide Hard Drives Together On my fairly modern motherboard, the cable is actually colour coded so you know which end plugs where – but more than likely your old PC won’t be, so you’ll need You may wish to make sure the hard drive is correctly installed before replacing the covers, but it is advisable to replace the covers before reconnecting the mains. http://www.makeuseof.com/tag/install-ide-hard-drive/ On even older mainboards you'll find a 32 GB limit.

Drives come defaulted to be ready to be installed in a single drive environment. Seagate Ide Hard Drive Jumper Settings Just clicking next until you get here. Now, assuming it is detected and working, go to the place where you set the Boot Priority Sequence. Thanks in advance Sep 15, 2009 #1 SNGX1275 TS Forces Special Posts: 10,715 +397 Set the jumper on the IDE drive to Master.

Sata And Ide Hard Drives Together

Reproducción automática Si la reproducción automática está habilitada, se reproducirá automáticamente un vídeo a continuación. http://www.helpwithpcs.com/upgrading/installing_cd_recorder.htm by R. How To Connect Ide Hard Drive To Sata Motherboard If the drive you have just installed is the only drive then you will need to install an operating system (if none present). Ide Hard Drive Jumper Settings Deshacer Cerrar Este vídeo no está disponible.

Install your OS on your IDE drive, go in the BIOS and make it so it boots off this HD (Make sure it's on Primary Master with the jumpers). http://secondsolution.net/hard-drive/installing-xp-on-a-slave-drive.php Cerrar Más información View this message in English Estás viendo YouTube en Español (España). This is really disturbing, if anyone can help that would be great. 0 CBeatZ825 11 Years Ago Well I figured out my own problem! Other then that minor problem everything else works fine. How Many Hard Drives Can Be Connected To A Single Ide Cable

You can guess the result.-> Also, XP will mark the drive as non-bootable and others weep as they have to repair it when they stick it back in the old machine.Bob If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). The EIDE maxtor I have has been set to slave (jumperless in this case). navigate here What are jumpers?

I see on the motherboard there are 2 sata plug in's. How To Connect Ide Hard Drive To Motherboard Now figure out where your additional drive is going to go. If not, email their support.

Sorry to insult the intelligence of the guys that use this, but I thought I'd make it as simple as I would have wanted to read it in this situation-written for

are there any known issues with these types of converters?? I havnt had any problems. I also had to change this. How To Install Ide Hard Drive It is sometimes easier to remove the IDE data cable and the power cable (labeled A and B in fig 1.1) before you remove the fixing screws (see fig 1.1), as

Master should be selected if this will be the only device on a single IDE cable or if it is the second device to be connected and the other device is I have Windows 2000 with an AMD 2800 chip and A7V8X mobo. Format the drive. his comment is here What does this mean?

Storage forum About This ForumCNET's Forum on storage is the best source for finding help, troubleshooting, and getting buying advice from a community of experts. so it installed onto C: and put a windows folder on D: as well as the stuff already there.that just blew my mind so i thought i better get sum help>i TigerDirect 366.458 visualizaciones 5:57 Cable o Adaptador de Corriente SATA a USB CASERO - Duración: 13:42. The problem of reinstalling Windows on a SATA boot device still happens with XP, but almost the first message from Windows asks you to "press F6 to install a Raid controller".

Attaching the SATA cables SATA data cables, labelled A in our diagram are standard and will only insert one-way. The OS now loads from the SATA HD and the EIDE HD was assigned a new drive letter on it's own and everything is functional. When you try to install a really big hard drive into a lot of older systems, you'll find that the BIOS is only capable of seeing 137 GB. You should be able to see some kind of message on the screen when it first posts indicating what you need to push.

the storm is coming Thanks I had the same problem with my system and it took me a while before I figured it was really simple to fix. SO just remove your SATA Drive... they are not slave or master on a cable. I had 4 devices working through 2 EIDE ports including my WD hard drive and then a Seagate HD through primary on SATA.

Wonder what connects to where on the cable?