Home > How To > Installing A CD/RW Correctly. Master/slave

Installing A CD/RW Correctly. Master/slave

Contents

The next step is to insert the drive into its new home. The color stripe on the cable must be aligned with pin-1 on the motherboard connector (Figure 4). Next, connect the 40-pin IDE/EIDE interface cable (large gray ribbon cable) to the back of the CD-ROM drive. However, if you require one of the other types of cable shown in the table below, you'll need to purchase it separately: Audio Connection Cable required How to connect it MPC this contact form

Another cause could be a real-mode (DOS) driver loading in the Config.sys file. If you have problems try treating them like a loose tooth, gently but firmly pulling while rocking the cable slightly from side-to-side. If the CD burns and ejects, you're not done. Connect the IDE ribbon cable to the back of the DVD RW. http://www.computerhope.com/issues/ch000415.htm

Ide Cd Drive Jumper Settings

A rear view of the Sony DVD RW looks like this. It includes instructions for both SATA and IDE types. Unless the device itself works, no CDRW functions will work.

Put the DVD on as the Slave on IDE 1. Once you have your CDRW drive ejecting, it's time to configure its SCSI simulation... Connect to Sound Blaster-compatible sound card and to analogue audio output connector at the rear of the drive. How To Connect Ide Dvd Drive To Sata Motherboard In truth, the more modern your system, the less likely is that the way in which you configure your IDE channels will make an appreciable difference to performance.

The connectors for the 40-wire IDE ribbon cable and 80-wire IDE ribbon cable are identical on both the motherboard and the back of the drive. How To Connect Cd Rom To Motherboard In the image you can see a typical SATA connector on a motherboard. This cable has one side of the cable that is red or blue indicating PIN 1. http://www.helpwithpcs.com/upgrading/installing_cd_recorder.htm See also: [ Linux Library | Troubleshooters.Com | Email Steve Litt | Copyright Notice ] Copyright (C)2001-2002, 2004 by Steve Litt. -- Legal Toggle navigation Search Submit San

Install an IDE drive The first step after removing the case covers is to remove the "blank" plastic front from the position in which you want to install the CD/DVD writer How To Connect Dvd Drive To Motherboard Sata The enlarged picture shows both very well. For the purposes of this example, let's say it's /dev/hdc. ALWAYS TURN THE POWER SUPPLY'S SWITCH TO 0 IF IT HAS ONE, OR IF IT DOESN'T HAVE ONE UNPLUG THE UNIT FROM THE WALL.

How To Connect Cd Rom To Motherboard

If you are upgrading an old SATA drive then you can use the same cables, if not then you will need to install a new cable from the motherboard to the original site Audio connector: If appropriate, you may connect the CD-ReWriter's analogue audio output connector to an audio amplifier or a sound card's internal audio input connector using a sound cable terminated with Ide Cd Drive Jumper Settings This is due to the well documented "ISO-9660 filesystem read ahead bug". Why Is It Necessary To Partition The Hard Disk While Installing Operating System? In this case the existing CR-ROM drive was relocated so as to allow this.

caution: Before performing any installation on the inside of a computer, it is important to discharge any static build-up, by touching an available metal surface before touching anything inside the computer. http://secondsolution.net/how-to/installing-new-ssd.php Some crucial ones are rockridge and joliet extensions, which enable long filenames. HP Customer Support Z7_3054ICK0KGTE30AQO5O3KA30U7 hp-contact-secondary-navigation-portlet Actions ${title} Loading... Although longer 40-pin or 80-pin IDE ribbon cables exist, it's best not to use them unless absolutely necessary. How To Install Dvd Drive On Pc

There are three pairs of letters, corresponding to the three jumper pins, CS for Cable Select, SL for Slave and MA for Master. This side of the cable almost always points to where the power connects to the CD-ROM drive. Reply Gray Lentz May 27, 2015 at 10:20 pm clear and easy instruction, thanks. Reply Larry_m7 April 10, 2011 at 11:11 am Why would you want to play with IDE drives navigate here As long as both devices are jumpered to Cable Select, the devices should work properly, but again, it is better to use a standard IDE cable, like the one that ships

Slave should be selected if this will be the second device on a singe IDE cable, for instance, if you do not already have a CD-ROM drive then you could attach Why Do Some Sound Cards Need Two Separate Sets Of I/o Addresses For older systems this may still be an important consideration. You must compare its contents to the original file.

Once all connections are made and checked, place the unit right-side-up, plug it into wall current, switch the power supply switch to the 1 position, and power up the computer.

Search all support All Support Software, Drivers and Updates Troubleshooting How to Product Information User Guides Cancel Example: “Laserjet P1102w driver” or “HP Pavilion 17-f002na will not turn on” Loading Results Physical Installation ALWAYS OBSERVE STATIC ELECTRICITY CAUTIONS. Neither device on an IDE channel is detected after the HP DVD/CD Writer drive installation This may be a master/slave jumper problem. Ide Hard Drive Jumper Settings You should take an hour to familiarize yourself with its man page.

Here is how the back of the Sony DVD RW drive looks inside the computer case with these two connections made to the back of the drive. Run the rmmod command several times until told it's not loaded: [[email protected] root]# rmmod ide-scsi[[email protected] root]# rmmod ide-scsirmmod: module ide-scsi is not loaded[[email protected] root]# Now load the ide-scsi module as Finally, connect the Molex style power cable to the back of the CD-ROM drive. his comment is here Then run lilo again.

There are 3 options, Cable Select, Slave and Master. Anything longer than this will tend to degrade the signals coming down the lines of the cable. As stated before, make sure the CDRW is connected to a normal IDE port, not an enhanced port. Some computers may require configuration changes in the BIOS specific to the IDE settings before Windows will detect the device and assign a drive letter.