Installing CD Rom
To install the drive, it will be necessary to remove a 5.25" drive slot cover from the case. This can normally be done by wearing anti-static wrist band or if unavailable, holding the metal part of the screwdriver for about two minutes. Wird geladen... Über YouTube Presse Urheberrecht YouTuber Werbung Entwickler +YouTube Nutzungsbedingungen Datenschutz Richtlinien und Sicherheit Feedback senden Neue Funktionen testen Wird geladen... You need to copy it over before you start. this contact form
Browse more how to's How to Install a CD Drive on a Computer How to Install a CD Player How to Install a CD-ROM Drive How to Install a Car Speaker List How To Install a CPU and Heatsink Article This Terminal Trick Will Eject a Mac's Stuck CD/DVD Article How to Preserve Your Vinyl Records by Backing Them Up to CD If you have troubles with this procedure, it may be due to a hardware problem, but it is also highly possible that the driver install program has done something stupid. Flag as...
How To Install Cd Drive In Laptop
The method for installing the drive will vary depending on the case. You can change this preference below. Step 9 Once in the BIOS settings; make sure that the drive is accurately recognized. What should I do if my PC cannot recognize the drive?
Each device is to be placed on the appropriate mode. Bear in mind the notes I put in at the top of this procedure about how sometimes the install programs don't set up the files properly. Melde dich an, um unangemessene Inhalte zu melden. How To Install Dvd Drive In Laptop Software Required: CD-ROM driver disk.
These instructions are valid for any form of optical based drive such as CD-ROM, CD-RW, DVD-Rom or DVD burners. How To Connect Cd Rom To Motherboard For example I got 3GB/s and 6GB/s, Hard Drives for 6GB and DVD-ROM Drives for 3GB.More CommentsAbout This Instructable 176,077views5favoritesLicense:piggycdzFollowMore by piggycdz:Add instructable to: Contest GroupRelatedMaking a Computerby Redfox888888Secret door Procedure Overview: Difficulty Level: 2-3 (Low to Moderate).
The two most common methods for installing a drive into a case is either through drive rails or directly into the drive cage. Rails: Place the drive rails onto the side
What am I doing wrong? How To Connect Dvd Drive To Motherboard Sata Wird geladen... Powered by Mediawiki. For IDE drives, align pin 1 (the red edge) to the connector on the CD/DVD drive.
How To Connect Cd Rom To Motherboard
What can I do? http://www.wikihow.com/Install-a-CD-ROM-or-DVD-Drive Answer this question Flag as... How To Install Cd Drive In Laptop Hinzufügen Playlists werden geladen... Install Dvd Drive Windows 7 Your computer's BIOS should recognize the new CD/DVD drive.
Melde dich an, um dieses Video zur Playlist "Später ansehen" hinzuzufügen. weblink Hochgeladen am 03.05.2009this guide will show you how to install a CD/DVD combo drive into your desktop computerPlease SUBSCRIBE if you like my videos Kategorie Praktische Tipps & Styling Lizenz Standard-YouTube-Lizenz Melde dich bei YouTube an, damit dein Feedback gezählt wird. Wird geladen... Cd Drive Installation Software
Verify that the location that you are connecting this cable to is NOT the jumpers on the back of the drive; while it may be possible for the cable to connect Melde dich bei YouTube an, damit dein Feedback gezählt wird. Then connect the 4-pin power connector to the drive. navigate here Answer this question Flag as...
Thank you for signing up. Dvd Drive Power Cable It's a common problem, that should fix it. Note that it can take a few seconds for the disk to be registered, so be patient.
I am getting an access denied error when trying to install a drive.
The installation process for the CD drive is generally similar to how a hard drive is installed into a desktop computer system. The only thing left to do is return power to the computer. Bitte versuche es später erneut. Optical Drive Sata Cable Wird geladen...
If the drive is to run on its own IDE cable, then plug the cable to both the motherboard and the CD drive. Materials Needed:- Screw remover and extractor- ATA cable- CD device driver Step 1 The first step to any hardware installation process that would require the opening of the computer casing is Wähle deine Sprache aus. his comment is here For example, if this drive is being attached to the same cable as your hard drive, the CD-ROM drive needs to be set to Slave and the hard drive needs to
They'll just say "MSCDEX not found" and stop. "C:\DOS" is the traditional place for the MSCDEX.EXE file on older DOS 6.22 and earlier PCs. You can do this the easy way or the hard way: Using an Editor: Create an empty file using your editor, and then save it as "CONFIG.SYS". Answer this question Flag as... The usual preference is the topmost available bay.
The steps were easy and clear. Please try again. Plug the cable into the connector labeled as CD Audio.7 Attaching the Drive Cable to the CD/DVD Plug the IDE Cable to the CD/DVD. ©Mark Kyrnin At this point, the Sprache: Deutsch Herkunft der Inhalte: Deutschland Eingeschränkter Modus: Aus Verlauf Hilfe Wird geladen...
Some CD-ROM driver install programs are totally brain-dead. Browse more how to's How to Install a CD-ROM Drive How to Install a Car Speaker How to Install a Computer How to Install a Computer Power Supply How to Install Wird verarbeitet... You can change this preference below.
For more information, refer to the page on CD-ROM configuration. This will create the AUTOEXEC.BAT file. Flag as... If the drive is going to be on its own cable, plug the IDE cable into the motherboard and one of the other connectors of the cable into the CD/DVD drive.
If the drive is going to reside on its own IDE cable alone, the drive should be set to the Master mode.5 Placing the CD/DVD Drive into the Case Slide If the CD/DVD drive will be an extra one, set the jumper setting to "Slave". 9 Slide the CD/DVD drive into the drive bay on the computer. 10 Move the cables The steps were easy and clear. A 3-pin Molex connector should be available from the power supply.