Home > How To > Installing Slave Drive Help Needed

Installing Slave Drive Help Needed

Contents

This will improve airflow and lead to a cooler system, but is not a critical concern. 7 Secure the hard drive. Your computer should see and read your drivejust fine. Reply cezar August 6, 2016 at 9:56 pm I have an old sata HD that came with the PC but the capacity was way to small, so i put in my If it is, perhaps you could have the system set up to look to the 2nd drive as an alternative boot drive if there is a problem with the primary.5. this contact form

TX Reply thenson on August 14, 2007 at 9:51 pm I was told that I fried my mother board from a local docal {dumb corner guy) 2nd hand computor store. Flag Permalink This was helpful (0) Collapse - Re: Sounds like good advice, Thor2k by Stephen714 / September 2, 2004 10:16 PM PDT In reply to: Sounds like good advice, Thor2k Most IDE ribbon cables come with three connectors: one on the end (usually black) and one mid-way (usually gray), then one further away on the other end which connects to the Steps Method 1 Desktop Hard Drive 1 Power down the computer.

How To Install A Second Hard Drive Windows 10

Stand up for your right to repair. I have them reconnected this same way. In addition, if giving the drive away, I would be sure to be responsible to help the kids when the drive does fail. If you are permanently installing an old drive on a new computer you may be slowing the system down a bit.

Flag Permalink This was helpful (1) Collapse - A new pc by grandpaw7 / August 27, 2004 7:31 AM PDT In reply to: Re: addendum Berfert, I guess the root reason Ideally you should use two screws on each side of the hard drive. Reply Robert March 20, 2015 at 11:37 am Can I add my old hardrive to a newer machine? How To Connect Two Sata Hard Disk In One Pc Stand up for the right to repair in Massachusetts.

Using SATA with Older Motherboards Motherboards made before Spring 2003 lack native (chipset-level) SATA support. Replace the case sides and reconnect your cables if you had to move the case to work on the inside. The new drive should appear on the BIOS boot screen as the system boots. Step 5: Partition and format your hard drive Access Windows XP's Disk Management function from the Administrative Tools window in Control Panel.

Flag Permalink This was helpful (0) Collapse - Re: Install old hard drive as slave drive? Slave Hard Drive That's another option.Hope this helps. Reply Rivers on August 4, 2007 at 2:07 am I installed a extra hard drive in my pc and would like to completely wipe all data from it. My PC is running on 2000XP with FAT32.

How To Install A Second Hard Drive Windows 7

It requires manufacturers to provide owners and independent repair businesses with fair access to service information and replacement parts. http://www.wikihow.com/Add-an-Extra-Hard-Drive Reply Douglas on September 26, 2009 at 3:28 pm Oh My God! How To Install A Second Hard Drive Windows 10 YesNo Feedback E-mail Share Print Search Recently added pages View all recent updates Useful links About Computer Hope Site Map Forum Contact Us How to Help Top 10 pages Follow us How To Install A Second Sata Hard Drive Don't know if it's important, but i'm running XP.

My computer - "C" drive properties still shows the 90GBI am running XP. - Sytem came right up and looks OKHow do I get "My Computer" to recognize the 250 GB. weblink All is good except for the fact that my hard drive has a "C" and an "I". These might be tucked away somewhere, so follow the other power cables carefully and try to find a spare one. If it can't reach the empty bay, see if any bundled adapters help. How To Slave A Sata Hard Drive

I'm familiar with computers but this is the first dual setup I have seen. But only you can decide what is best for you and your wallet. Reply Boston Brady August 30, 2016 at 4:11 pm I have a Lenovo ThinkServer TS140, I see only 2 sata cables; 1 for hard drive and 1 for DVD....Can I add navigate here I plugged all three in and my computer screeched at me!!!!

System runs windows xp.If I look at the drives in computer management, both drives show up as healthy, but one is labeled "system" and the other is labeled "page files" There Master Slave Hard Drive Setup You will need to remove both sides so that you can screw the hard drive in on both sides. /images/thumb/0/07/Install-a-Hard-Drive-Step-2-Version-2.jpg/550px-Install-a-Hard-Drive-Step-2-Version-2.jpg /images/thumb/0/07/Install-a-Hard-Drive-Step-2-Version-2.jpg/300px-Install-a-Hard-Drive-Step-2-Version-2.jpg /f/f5/Install a Hard Drive Step 2.360p.mp4 3 Ensure that you However, the word 'need' is misleading, as you can use a lot of different hard drives in some laptops.

IDE drives are becoming increasingly harder to buy, and it’s a good indication your computer is really getting old.

One is used by my system hard drive (the drive that came with my computer), and the other is used by my SATA CD/DVD drive. I managed the installation of the hardware on my own, but was at a loss on how to assign the drive letter. If you plan on using another operating such as Linux or Unix, disk partitioning will be performed during the installation process. How To Connect Two Hard Disk In One Pc But, for example, if you are installing a new Seagate hard drive in a system that already has a Maxtor drive installed, you can generally use either manufacturer's disk preparation utility.

Some systems add SATA support with a PCI SATA host adapter. However, if you want to preserve the information, it's a better idea to transfer the information to a permanent form of storage such as CD-R's (recordable cd's). Figure 7-8: Securing a hard drive in a drive tray Where's the Power Cable? his comment is here Flag Permalink This was helpful (0) Collapse - Re: Install old hard drive as slave drive?