Home > Installing Xp > Installing Xp On NTFS Gets BSD At "Registering Components."

Installing Xp On NTFS Gets BSD At "Registering Components."

B) if the problem is Hardware-related (rare but it happens) : 90% of "no boot" problems are caused by software. Burke Jr. I have removed the extra RAM from the laptop nothing else I can remove for now. If you don't like this, please don't read any further. navigate here

Now the installation goes as far as 18 mins left but freezes on "registering components" part. Thanks nitinpai donji Says: April 8, 2007 at 1:21 pm had to delete 4 "infs" including machine .inf over 4 reboots >>>works great now!!! You will be prompted for Computer Name and Administrator password. The true answer is when you actually try a remedy and it works! anchor

i finally solved 34 minute problem… gratzc Says: March 8, 2007 at 8:50 pm THANK YOU. Thanks in advance, Robert Alex Says: December 18, 2006 at 1:27 pm Wow, thanx. I re-install every 6 months just for the practice.Since you did a FAT install of Windows, you opened you OSX side to problems.

First steps common BIOS -In Integrated peripherals setup menu under onboard PCI device, enable Serial ATA controller. -Save bios end reboot. -Enter bios a second time. -Enter advanced BIOS feature setup If its a bad sector problem then your hard drive ougt to be replaced. New harddrive, expect same mshdc.inf line, but this time around it is machine.inf, which I left. Depending on your XP edition, a licence agreement screen may appear.

Go ahead and delete it. NTFS Windows is foreign enough that OS X cannot "see" it very well and you are much better protected. Any tricks here I should know about or problems with SP2 and SATA drivers ? Thanks again!

then i can get to the screen where it asks you to go to safe mode or start windows normally, but if i choose start windows normally it loads and restarts And yes.. If you have an earlier version, it is recommended to slip stream Service Pack 2 into it and create a new CD for security reasons. Then consult your manufacturer website on another PC or call their support - additional beeps are codes that tell you what hardware is malfunctioning - common culprits includes the memory chips,

Excellent and thank you very very much posted 25 Apr 2008 - Reply - Permanent Link Roland A. http://www.theeldergeek.com/forum/index.php?showtopic=19571 I WILL GIVE ***** STARS 4 U. For example, the device pathname format for a standard bootable drive C configuration would look like this: \Device\HardDisk0 #8: Disable automatic restart When Windows XP encounters a fatal error, the default Then when you get into Windows, go to: Start/Programs/Accessories/System Tools/System Restore, and restore the most recent Restore Point.

At any rate, a chkdsk will have no effect on your OS X partition or boot sector. http://secondsolution.net/installing-xp/installing-xp-on-md-96630.php I deleted it and it sent my comp into the BSOD reset loop. It saved another computer. My prompt looks like this: C:\Windows\system32> and I have tried as you said to enter: C:\Windows\system32>cd..

C:\Windows\inf>del oem11.inf Hope this works.. posted 30 Apr 2008 - Reply - Permanent Link Sherri Unregistered Woweee!! Ganesh. 21 comments new post [ expand all ] Page: Prev 1 2 Next Show All mariam (1 posts) thanks for all, you know i didn't learn this in class but http://secondsolution.net/installing-xp/installing-xp-pro-over-xp-home.php If you are using scsi(x) in the Boot.ini file, copy the correct device driver for the SCSI controller in use on the computer to the root of the Setup disk, and

You can also try out the windows 2000 solution I have told in my comment above. Once the initial preparation is complete, you'll see the Windows XP Setup screen (shown earlier in Figure A). i have been looking for this solution for ever!

If it is malware, then the real answer is a fesh install.

The screen will say "To setup Windows XP now, press ENTER" - so hit Enter. Trouble signing in, accessing... The information here is accurate to the best of my knowledge. Please help…I'm soooo close…I think?

I noticed a couple of the issues the setup is having with installation is with things labeled VIA whereas my mobo is now using an Nvida Nforce chipset… any other ideas Tech Support Guy is completely free -- paid for by advertisers and donations. When Windows XP begins to boot up and you see the message┬áPlease select the operating system to start or hear the single beep, press [F8] to display the Windows Advanced Options http://secondsolution.net/installing-xp/installing-xp-over-2kpro.php Kevin Says: January 8, 2007 at 6:01 am Michael, This was similar to the situation I was in prior to repairing my Windows install.

remove all cards except for the video card, and remove all extra memory except the one in the first memory bank. Then rename "Program Files" to "Progbak", and Windows to "Winbak" - of course if you do not have enough drive space, use Deltree to get rid of those folders (it takes